Imported chrome green non-metallic floor hardener
Imported chrome green non-metallic floor hardener Product Overview: Imported Chrome Green Non-metallic Ground warehouses, underground parking lots, machinery manufacturing plants and other places require that the ground cannot be sand and can withstand the rolling of various vehicles (such as cars, forklifts, carts, etc.), so these places The floor should not only have the flat and smooth decorative effect of the general floor protection system.
It also needs to have strong wear resistance and compressive resistance. Therefore, emery sand - resistant floor is a kind of floor system that specializes in the ground protection of heavy machinery manufacturing enterprises, industrial and commercial warehouses, underground parking lots and so on.Hard Acrylic Courts,Green Hard Acrylic Paint,White Hard Acrylic Paint.
Imported Chrome Green Non-metallic Floor Material Applicable place:
The ground of special places such as supermarket, building hall, warehouse, automobile exhibition hall, automobile repair shop and underground parking lot;
The area with high mechanical performance requires a certain impact mechanical, electronic, electrical, instrument, medicine, textile, clothing, food, tobacco and other enterprise factory floor.
Industrial plant, workshop, warehouse, logistics center, garage, parking lot, supermarket, etc.
1. The grounds of special places such as supermarkets, buildings, warehouses, auto showrooms, auto repair shops, and underground parking lots;
2. The area with high mechanical performance requirements has a certain impact on machinery, electronics, electrical appliances, instruments, pharmaceuticals, textiles, clothing, food, tobacco and other corporate plant floors.
3, industrial plants, production workshops, warehouses, logistics centers, garages, parking lots, supermarkets and other ground,Red Hard Acrylic Paint.
Imported Chrome Green Non-metallic Floor Product features:
1. Resistance to impact, pressure and mechanical performance;
2. Dustproof, mildew proof, abrasion resistance, good hardness;
3. Anti-stress, abrasion resistance, dust removal, enhanced surface oil resistance, anti-penetration;
4. The appearance is smooth and bright and colorful;
5. Convenient for cleaning and maintenance.
Non-Metallic Ground Hardener Basic requirements:
1. The concrete strength of the grass-roots level should be above C25, the water-cement ratio should be controlled below 0.50, the concrete fall-out difference should be controlled within 70-100mm, and the concrete mixture should minimize segregation and control the bleeding.
2. In order to ensure that the concrete mixture has sufficient fluidity and conducive to construction, it is recommended that concrete be added with proper additives.
3. The concrete of the grass-roots level shall be cast and tamped with reference to the standard of the fine concrete. Note that the accurate size and the reduction of laitance production.
4. The hardener surface should be constructed at the same time as the concrete structure layer. If the same leveling layer is to be used at the same time, it is recommended that the leveling concrete should be fine stone concrete with a thickness of not less than 50mm, and consider deploying a telescopic reinforcement mesh.
5. Pay special attention to the corners of the primary concrete construction block to ensure that the concrete is vibrated and compacted and additional strengthening treatment should be taken.
1. Surface treatment: using the mechanical trowel of the packing disc to remove the slurry layer of the concrete surface evenly;
2. The first spreading material: after the concrete surface with the specified amount of 2/3 hardened and wear-resistant floor material is uniformly distributed on the concrete surface of the initial stage, it shall be polished with a low speed smoothing machine;
3. Leveling: use 6 meters to scrape the hardened wear-resistant materials evenly along the horizontal and longitudinal direction and give a rough leveling;
4. The second spreading material: it will be required to use 1/3 color hardened wear-resistant material uniformly (on the surface of abrasion resistant material that has been polished for the first time), and then rub it again with the smoothing machine;
5. Surface polishing: according to the hardening condition of concrete, adjust the Angle of the blade of the polishing machine, polishing the surface layer to ensure the surface smoothness and finish;
6, base expansion: wear-resisting hardening floor after completion of the construction of 4 ~ 6 hours, should be on the surface of maintenance, to prevent surface water evaporation, sharply to ensure the steady growth of wear-resisting material strength.Concrete Seal Curing Agent.
Looking for ideal Hardener for Epoxy Resin Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Hardener for Paint are quality guaranteed. We are China Origin Factory of Hardener for Polyester Resin. If you have any question, please feel free to contact us.
Product Categories : Ground hardener system > Non-metallic Ground Hardener