Imported chrome green metal surface hardener
Imported chrome green metal surface hardener Product overview:
Imported Chrome Green Metal Floor Materials is suitable for the warehouse, underground parking, machinery manufacturing enterprise workshop etc for the ground cannot rise sand dust, and can withstand all kinds of vehicles (such as car, forklift, cart, etc.) of roll-off, so these places of floor not only has general floor protection system level off,Smooth decorative effect, also need to have strong wear resistance and compression resistance. Therefore, the corundum wear-resistant floor is a floor system that professionally solves ground protection problems such as workshops, industrial and commercial warehouses, and underground parking lots for heavy machinery manufacturers.Anti-Static Epoxy Topcoat,Grouting Material.
Imported Chrome Green Metal Wear Floor Applicable place:
1. The grounds of special places such as supermarkets, buildings, warehouses, auto showrooms, auto repair shops, and underground parking lots;
2. The area with high mechanical performance requirements has a certain impact on machinery, electronics, electrical appliances, instruments, pharmaceuticals, textiles, clothing, food, tobacco and other corporate plant floors.
3, industrial plants, production workshops, warehouses, logistics centers, garages, parking lots, supermarkets and other ground,Cement Grouting Material.
Imported Chrome Green Metal Material Product Features:
1, impact resistance, heavy pressure, good mechanical properties;
2, dust, mold, wear, hardness is good;
3, resistance to heavy pressure, strong wear resistance, can not afford dust, enhance the ground oil resistance, anti-infiltration;
4, the appearance of smooth, bright colors and diverse;
5, easy to clean, easy to maintain.
Metal Floor Hardener Basic requirements:
1. The concrete strength of the grass-roots level should be above C25, the water-cement ratio should be controlled below 0.50, the concrete fall-out difference should be controlled within 70-100mm, and the concrete mixture should minimize segregation and control the bleeding.
2. In order to ensure that the concrete mixture has sufficient fluidity and conducive to construction, it is recommended that concrete be added with proper additives.High Strength Grouting Material.
3. The concrete of the grass-roots level shall be poured and tamped with reference to the standard of the fine concrete. Note that the accurate size and the reduction of laitance production.
4. The hardener surface is preferably constructed at the same time as the concrete structural layer. If the same leveling layer is to be applied at the same time, it is recommended that the leveling concrete should be fine stone concrete with a thickness of not less than 50mm, and consider deploying a telescopic reinforcement mesh.
5. Pay special attention to the corners of the primary concrete construction block to ensure that the concrete is vibrated and compacted and additional strengthening treatment should be taken.
1.Surface treatment: using a mechanical rake equipped with a disc to evenly remove the laitance layer on the concrete surface;
2. Distribute the material for the first time: Spread the prescribed amount of 2/3 hardened wear-resistant floor material evenly on the concrete surface of the initial setting stage, and then use a low-speed smoothing machine to perform the grinding treatment;
3, Scratch ruler leveling: with 6 m scraping ruler, the hardened and wear-resistant material is evenly wiped horizontally and longitudinally and roughly leveled;
4. Disperse the material for the second time: Dispense the specified amount of 1/3 color hardened and wear-resistant material evenly (on the surface of the first abrasion-resistant material), and polish again with a trowel;
5, surface polishing: According to the hardening of the concrete, adjust the angle of the blade on the polishing machine, polishing the surface to ensure that the surface roughness and finish;Non-Shrinkage Grouting Material.Acrylic Court Coating.
6, base surface expansion: wear-resistant hardened floor within 4 to 6 hours after construction is completed, should be maintained on the surface to prevent the rapid evaporation of surface moisture to ensure the steady growth of wear-resistant material strength.
Looking for ideal Imported Chrome Green Metal Floor Materials Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the Imported Chrome Green Metal Wear Floor are quality guaranteed. We are China Origin Factory of Imported Chrome Green Metal Material. If you have any question, please feel free to contact us.
Product Categories : Ground hardener system > Metal Floor Hardener